Browse Categories
Search

15KW (30-80Khz) Dual Station Bench Top Induction Heater with Timer Control & Temp Controller Port - SP-15AB


In stock
Item Number: SP-15AB
SP-15AB Dual Station 15KW Induction Heater is designed for material research lab to quickly melt and perform heat treating to metallic materials up to 1kg. The 2m long power cable allows heating station and the control station being located up to 2m from each other for operation safety. 
 
SPECIFICATIONS:
Working Voltage
208-240V AC, 50/60 Hz, Single Phase
Max. Input Current
  • 34 Amp  (Min. 40A breaker required)
  • Power cable included (It is suggested to use NEMA L6-50P twist-lock plug with 10AWG power cable)
Output Frequency 30-80 kHz
Heating Current 200-600 Amp
Maximum Oscillating power 15 KW
Max. Input Power 7 KW
Duty Cycle 80%
Max. Distance Between Heater and Controller 2m
Max. Sample Weight 1 kg
Option Control Station
  • Automatic timer control or  Manual control selectable
    • Manual Control: by Foot Pedal
    • Automatic Heating Time: 1-99 Seconds
    • Automatic Dwell Time: 1-99 Seconds
    • Automatic Colling Time: 1-99 Seconds
  • One Portis is built in to connect to the temperature controller and thermal couple, which can control temperature automatically via optional control unit.  Please click the picture below to order at extra cost.
Air Cooling Rear Fan
Water Cooling

  • Flowrate: 2~5 L/Min
  • Pressure: 0.2 MPa (29 Psi)
  • Protection: Over-pressure and over temperature switch
  • Tap water is acceptable, but using Recirculating Water Chiller is highly recommended. Please click the left picture to order separately at extra cost
Induction Coil & Accessories   
Display Digital display shows output power and current
Product Dimensions
  • Control Station: 18" x 8" x 17"
  • Heating Station: 12" x 8" x 13"
Warranty One Year limited warranty with lifetime support
Compliance
  • MET Certification (UL 1450) is available upon request at extra cost, please contact our sales representatives for quote. 
Operation Manual 
           











Application Notes
Melting
  
  Sintering
  
  Annealing
  
  Heat treatment
  
  Quenching
  • Please click here to learn how to setup crucible for melting
  • Heater will shut down if over output occurs. Pls reduce coil cycle number to keep heater operating under Max power
  • Melting time and temperature are related to materials, crucible, refractory insulation, etc. If you do not know whether the induction heater can melt your sample or not, please contact our engineer for consulting. Have your alloy's composition, melting point, and quantity to be melted prepared
  • You may melt metal sample in vacuum using 60mm dia half open quartz tube with vacuum flange/valve. Please click the picture below for details on how to setup the vacuum tube
  • You may need a graphite crucible with diameter < 54 mm to put inside quartz tube with some refractory material and covering lid to support the crucible
  • The Induction Melting System are designed for using under vacuum and low pressure < 0.02 MPa / 0.2 Bar/ 3 PSI   
  • Never heat the furnace while the gas release valve is closed and a positive pressure condition exists within the furnace chamber. The pressure gauge must be used to closely monitor the chamber condition at all times during the heating process; please open the gas release valve immediately once the chamber pressure has reached over 3 PSI to prevent unforeseeable damages.
  • The Pressure shall be regulated to< 5PSI and flow rate for gases should be limited to < 200 SCCM ( or 200ml/min ). Click here to learn more about the installation of a gas regulator.
  •     
  • For customization inquiries, please complete the "Customize Induction Heating System Form" and return it to info@mtixtl.com



Temperature Controller (Options)
  • In order to enable the temperature control function of this induction unit, please order the temperature controller               EQ-MTC-808
  • You may also to consider order the complete system EQ-SP-15TC from us

                         

Net Weight 25 kg (55 lbs)
Shipping Dimensions 40"(L) x 30"(W) x 30"(H)
Shipping weight (Pounds) 45 kg (100 lbs)

STANDARD PACKAGE:
Item Description Qty Pictures
1 Heating Station 1
2 Control Station 1
3 Coil #1: 76.8mm(OD) x 66.0mm(ID) x 40mm(H) 1
4 Coil #2: 82.5mm(OD) x 65.5mm(ID) x 73.5mm(H) 1
5 Cable for connecting Heating Station and Control Station 1
6 Foot Pedal with Cable 1
7 Water Cooling Fitting and clamp (Pipe is not included) 1
8 Fuses 4

Related Products

Shopping Cart
Your cart is empty.
Please clear the browsing history before ordering the product. Otherwise, availability and price are not guaranteed.
Mailing Lists
MTI sponsors MTI-UCSD Battery Fabrication Lab:
MTI-UCSD Battery Fabrication Lab Opening


MTI sponsors MRS and ECS Postdoctoral Award:

MTI Sponsors the Postdoctoral Awards

Upcoming Shows:
2017 MMM Conference Nov 6-10 Pittsburgh, PA Booth 9

2017 MRS Fall Meeting and Exhibit Nov 26 - Dec 1 Boston MA Booth 901

2018 SME Annual Conference & Expo Feb 25 - 28 Minneapolis, MN Booth 701

Recent Attended Shows:
MS&T 2017 Oct 8 - 12 Pittsburgh, PA

232nd ECS Meeting Oct 1 - 5 National Harbor, MD

The Battery Show North America 2017 Sep 12-14 Novi MI

Click here to see our past conferences

 

Notices
1. Prices listed online are valid for US market and whom pay by credit card only. There will be extra charges for shipping & handling. Price various from country to country.
2. We may add extra charges for paper order and net30 terms due to extra labor cost.
3. The prices listed are subject to change without notice.