Browse Categories
Search

Ni-Based Super-alloy High Pressure Hydro-thermal Reactor 1100°C, Optional Volume 65ml & 100ml -GSL-1100X-RC series


Product Options

UL/CSA/CE Certifications:
Vessel Volume:
RC-Ni is reactor made of Ni-Base Superalloy, which has excellent creep strength and anti-oxidation. It can reach 1100 °C with a pressure up to 4Mpa under oxygen or inert gas. It is an ideal tool for preparing advanced material by the hydrothermal method, especially heat treat sample under high oxygen pressure. A solenoid valve is installed on the flange allows auto-pressure relief control. Temp. Control and Pressure Real-time Monitoring software are also included. (new feature since 5/12/14
 
SPECIFICATIONS



Structure
  • Warning:   For your safety,  the high-pressure vessel and furnace must be placed inside an explosive-proof box or case during using under high pressure.  Never face on top flange without protection to avoid the accident.  
  • Please click picture and drawing below left  to see detail structure, and click pic right to order an Explosion-Proof Box 
                       
Working Voltage
  • AC 208~240V, Single  Phase
Pressure Vessel

  • Made of Ni-Based Superalloy, optional at 65&100ml ( click pic 1 to order spare )
  • Air cold flange via aluminum heat radiator
  • Liner inside vessel with various materials is available upon request at extra cost
  • Attention: Processing Tube is consumable part, you can click picture below to order replacement or spare one 
  • Ni-Based Superalloy High-Pressure Hydrothermal Reactor 
  • A small quartz or Alumina boat should be used to load the sample inside the vessel. Please click the link below to order separately. Never place the sample directly onto the vessel without a crucible. Vessel service-life could be reduced significantly if you do so.
  • You may use gold or nickel foil to wrap the crucible boat to minimize the contamination to the pressure vessel.
  •              
Product Dimension
Reactor Capacity & Dimensions
( Pls select the volumn in the option bar )
  • 55 mm OD x 20 mm ID x 214 mm height, 65 mL capacity
  • 65mm OD x 25mm ID x 210 mm height, 100 mL capacity
Working Temperature & Control

  • RT -  1100 °C Max.
  • Digital temperature controller with 30 segment programmable
  • Temperature accuracy +/- 1°C
  • Recommend heating rate <=10°C/min
Thermocouple
 
Working Pressure
  • 36 Mpa (5292 PSI)     Max  at 500°C
  • 24 Mpa (3528 PSI)     Max. at 800 °C
  • 14 Mpa (2116 PSI)     Max. at 900 °C
  • 7 Mpa   (1058 PSI)     Max. at 1000 °C
  • 4 Mpa   (588 PSI)       Max. at 1100°C 

Pressure Monitoring and Relief
  • Precision high-pressure sensor (measurement Range up to 250 bars) installed on the pressure vessel.
  • Pressure monitor can display pressure in Bar. It also allows the user to define the high-pressure alarm set point.
  • When the pressure reaches the alarm set point (Max.15Mpa), the pressure inside the vessel will be released via the solenoid valve installed on the flange. For Max.pressure >15 Mpa, please shut off the manual needle valve  nearby the solenoid valve.)



PC Control (optional)
  • MTS-02 control software is available for controlling and displaying temperature and pressure by PC 
  • PC control module is compatible with Labview software.
  • Pressure & Temp. Real Time Monitoring (This new feature is available since 5/12/14):   
                
Accessories
  • SS316 needle valve with 1/4 pipe connector & Pressure gauge included
  • Two Copper Gasket 48mm O.D are included, which is consumables
  • Pls click picture to order spare
  • The optional torque wrench is available here  to avoid overtightening the flange bolts.Please email us to learn the suitable tightening torque for the Hydrothermal Reactor.
  •        
Operation Instructions
     

Application Notes
  • Attention: A two-stage pressure regulator must be installed on the gas cylinder to limit the pressure to below 3 PSI for safe operation. Click here to learn the installation of a gas regulator.
  • Do not over tightening the flange screws as this may cause permanent damages to the flange or screws. Please refer to the instructions about proper torque for installing CF flange bolts.We recommend you use a torque wrench to tighten the screws with the flange.

Related Products

Shopping Cart
Your cart is empty.
Please clear the browsing history before ordering the product. Otherwise, availability and price are not guaranteed.
Mailing Lists
MTI sponsors MRS Postdoctoral Awards:
MRS Postdoctoral Awards Nomination
 

MRS Past Postdoctoral Award Recipients 


MTI sponsors ECS Battery Division Postdoctoral Associate Research Award 

ECS Battery Division Postdoctoral Awards Nomination 


Upcoming Shows:

Ceramics Expo Apr 25 - 27 Cleveland, OH Booth 1242

231st ECS Meeting May 28 - June 2 New Orleans, LA Booth 312

Beyond Lithium Ion Symposium- 10 BLX June 27 - 29 IBM San Jose CA

ICT 2017 Jul 30 - Aug 3 Pasadena, CA

Recent Attended Shows:

2017 MRS Spring Meeting & Exhibit Apr 17 - 21 Phoenix, AZ

253rd ACS National Meeting & Exposition Apr 2 - 6 San Francisco, CA Booth 1921


Click here to see our past conferences

 

Notices
1. Prices listed online are valid for US market and whom pay by credit card only. There will be extra charges for shipping & handling. Price various from country to country.
2. We may add extra charges for paper order and net30 terms due to extra labor cost.
3. The prices listed are subject to change without notice.