Browse Categories

One set of 3" Diameter ( I.D. ) Dry Pellet Pressing Die - EQ-Die-75D

In stock
Item Number: EQ-Die-75D
Extremely Heavy Item, special craft needed.

Quantity Discounts

2 to 5USD$756.20
6 to 9USD$716.40
10 or moreUSD$676.60


Modle EQ-Die-75D
Height 2 3/8" (60 mm)
Diameter 4 3/4" (120mm)
Weight 22 Lbs

Whole set  pressing die includes
    • Double layer structure 3" dry pressing die
    • One 3" I.D. die is inside, made of hardened steel and highly polished with hardness Rc 60 - 62
    • Ra 0.08μm highly polished steel
    • One stainless steel sleeve is in outside to protect die from cracking
    • Two pushing rods highly polished and perfectly fitted into die
    • Two steel support plates
    • One steel cylinder for releasing out sample
    • Max Compressive Pressure: 434 metric tons
    • Please must always wear protection goggles during operation !!!
    • The pressing die cannot be used for pressing powder with particle size < 30 mircon. Small particles may slip into the gap between pushing rod and steel sleeve and cause damages to the sleeve during the compression. Ball mill and sieve the powder and apply only the 32~75 mircrons powder to the pressing die to avoid the damages. Please consider using the 3'' Dia. Sieve Set No.200&450 Mesh to seperate the 32~75 microns particles from the powder clumps. Please clean the mould via ethanol after the completion of each experiment.
    • Please use alcohol to clean the pressing die every time before use and store it in a dry place with antirust oil after operation to avoid rusting on the surface, because all pressing dies are made by high-stretched carbon steel for achieving high hardness to meet essential requirements of making ceramic or metal samples. Otherwise, the pressing surface could probably get scratched.
    • To avoid damaging the die core and sleeve, we strongly recommend you use the professional labotory hydraulic pressers which ensure the most even pressing interface and uniform pressure force.
    • For pressing sticky metal powders such as Al, Mg, Zn, it is necessary to use dry or alcohol-based tool lubricant to lubricate the die and sleeve set to reduce friction during the compression.
    • Do not press flammable, explosive materials.
    Application Note
    • You may consider using EQ-BNMR for easy mold release. Please click the picture below to order.
    Steps to make sample pellet
    • Mixing and grinding chemical powder by agate mortar or Ball Mill
    • Calcine mixed the powder in a high temp furnace under suitable temperature
    • Crushing and Grinding calcined powder again by mortar or ball mill
    • Put calcined powder in to the die
    • Pressing sample by a pressing machine under suitable pressure
    • Take out pellet sample from die
    • Sintering the pellet under suitable temperature
    • Then, a new material sample is formed!ing Oven

    Related Products

    Shopping Cart
    Your cart is empty.
    Please clear the browsing history before ordering the product. Otherwise, availability and price are not guaranteed.
    Mailing Lists
    MTI sponsorships:
    MTI Sponsors Thermoelectrics Workshop

    MTI-UCSD Battery Fabrication Lab

    MTI Sponsors the Postdoctoral Awards

    Upcoming Shows:
    MS&T 2018 Oct 14-18 Columbus OH Booth 513

    2018 MRS Fall Meeting and Exhibit Nov 25 - 30 Boston MA Booth 901

    APS March Meeting 2019 March 4-8 Boston MA

    Recent Attended Shows:
    Furnaces North America Oct 8-10 Indianapolis IN

    AiMES 2018 Sept 30 - Oct 4 Cancun Mexico

    Zhejiang University MSE Visiting August 10th Richmond CA

    Click here to see our past conferences


    1. Prices listed online are valid for US market and whom pay by credit card only. There will be extra charges for shipping & handling. Price various from country to country.
    2. We may add extra charges for paper order and net30 terms due to extra labor cost.
    3. The prices listed are subject to change without notice.