Browse Categories

Roll-to-Roll Pilot Coating System with Optional Blade, Reverse Comma, Tape Cast, Slot Die, Micro Gravure Coating Heads- MSK-AFA-MC400

Please email for lead time
Transported by LTL Freight (Truck)

Product Options

Coating Head:

MSK-AFA-MC400 is a versatile R2R coating system which can adopt various coating heads such as reverse comma blade, Doctor Blade, Slot Die and Micro Gravure and Tape Casting. A 4.5 meters long, three-zone convection drying oven with independent temperature programming is implemented for efficient slurry curing. This is the most complete and universal pilot coating system that provides broad adaptability to various coating slurries and film substrates (Cu, Al, PET, PP, PE).

  • Doctor Blade: Cost effective solution for 10~200 micron thick coatings (Continuous mode only)
  • Reverse Comma Blade (Transfer Coating): Cost effective solution for 30~200 micron thick coatings (Both continuous & intermittence mode)
  • Tape Cast Coating: Ideal for performing thicker coating up to 1000 microns with high viscosity slurry
  • Micro-Gravure: Perfectly suitable for precise thin coatings from 1~3 microns (dry film thickness)
  • Slot Die: Suitable for precision coatings as thin as 1 micron while providing wide coverage for thicker coatings up to 200 microns

For Roll to Roll Coating Service, please fill out and submit the Roll to Roll Coating Service Request Form.


Working Voltage

208 - 240 VAC, 50/60 Hz, three Phase (380VAC three phase is available upon request)

Max. Power Consumption

30 KW ( 50A Air breaker required )

Compressed Air 

0.5-0.8 MPa is required (Air compressor not included. Please click here to order)
Attention: If a gas cylinder is used instead of air compressor(pic2), a two-stage pressure regulator(pic1) must be installed on the gas cylinder to limit the pressure within the required working range for safe operation. Click here to learn the installation of a gas regulator.
  pic1                pic2

Reeling/Unreeling Diameter

  • 350mm O.D Max. 
  • Reeling/Unreeling shaft diameter: 3 inches

Coating Width

350mm Max.

Coating Speed


Coating Heads (please select in the Product Options)

  • Reverse Comma Blade
  • Doctor Blade
  • Tape Casting
  • Slot Die
  • Micro-Gravure

Doctor Blade Coating
  • Continuous coating mode only
  • Coating thickness range: 10~200um  ( dried film )
  • Typical slurry viscosity range: 500~10000 mPa.s
  • Precision: ±5μm (gap adjustment solution 1um); Edge to center thickness tolerance +/-8um
  • MSK-155 auto-slurry feeder with 2 liters tank is available at extra cost, please click underline to view details.
Reverse Comma Blade (Transfer Coating)
  • Two available coating modes (continuous and intermittent) selectable on the control panel.
  • Coating thickness range: 30~200um  ( dried film )
  • Typical slurry viscosity range: 500~10000 mPa.s
  • Precision: ±3μm; Edge to center thickness tolerance +/-5um
  • MSK-155 auto-slurry feeder with 2 liters tank is available at extra cost, please click underline to view details.
Cast Coating
  • Tape casting technique is ideal for handling thicker slurry 5000~20000 mPa.s and thus thicker film coating is achievable (up to 1000um)
  • Continuous coating mode only
  • Precision: ±5μm (gap adjustment solution 1um); Edge to center thickness tolerance +/-8um
  • MSK-156 slurry feeding screw pump with 4 liters tank is included, please click underline to view details

Slot Die coating

  • The slot die is perfect for uniform film coating of 1 micron and up to 200-micron thickness. By changing the shim size with various patterns, you would be able to produce continuous, intermittent, or even grid coatings that match the shim patterns. Please refer to the pictures in below for more details:
  • MSK-156 slurry feeding screw pump with 4 liters tank is included, please click underline to view details
  • Minimum thickness & precision: 1 µm ( dried film ), ±1%  
  • Typical slurry viscosity range: 200~10000 mPa.s
Attention: The final coating thickness is dependent on a wide range of parameters such as slurry viscosity, solid particle size, solid content, shim thickness, foil rolling speed and slurry feeding rate. Therefore, we are not able to guarantee that 1-micron level film is achievable for all kinds of slurries. For further discussion, please let us know your slurry specs and coating thickness requirement.

Micro-Gravure Coating

  • Continuous and intermittent coating modes are available for the user.
  • Coating thickness range: 1~3um  ( dried film )
  • Typical slurry viscosity range: 30~1000 mPa.s
  • MSK-155 auto-slurry feeder with 2 liters tank is included, please click underline to view details.

Convection Drying Oven 

  • Three-zone design with independent temperature controllers.
  • Airflow rate:9.5/2800 ( cm³/RPM ) max. for a single zone, flow rate adjustable
  • Drying temperature: 150°C max ±5℃
  • Power Consumption: 9KW for single zone (27KW total)
  • Heater length: 1.5m for single zone (4.5m total)

Product Dimensions

L6600mm x W1200mm x H1850mm


  • CE Certified All electric components ( >24V) are UL / MET / CSA certified
  • NRTL or CSA certification is available upon request at the exta cost.


  • One Year limited warranty with lifetime support
  • Rusting and damage due to improper storage condition or maintenance are not covered by warranty
Operation Manual & Video
Application Notes
  • Customers are welcome to visit our facility to receive technical training before shipping of equipment (Please schedule an appointment with us in advance)
  • Onsite Training is available for customers within the US only (Expenses will be covered by customers)
Net Weight 12.3t

Related Products

Shopping Cart
Your cart is empty.
Please clear the browsing history before ordering the product. Otherwise, availability and price are not guaranteed.
Mailing Lists
MTI sponsorships:
MTI Sponsors Thermoelectrics Workshop

MTI-UCSD Battery Fabrication Lab

MTI-VISTEC Cylindrical Cell  Pilot Line

MTI Sponsors the Postdoctoral Awards

MTI and Celgard have successfully reached the settlement under court for the litigation on patent and trademark

Upcoming Shows:

2019 MRS Fall Dec 1 - 6 Boston MA Booth 901

AABC Europe Jan 12 - 16 Wiesbaden Germany

TMS 2020 Feb 23 - 27 San Diego CA Booth 301

APS March Meeting March 2 - 6 Denver CO

Recent Attended Shows:
236th ECS Meeting Oct 13 - 17 Atlanta GA Booth 200

MS&T 2019 Sep 29 - Oct 3 Portland OR Booth 614

ICT/ACT 2019 Jun 30 - July 4 Gyeongju South Korea

Click here to see our past conferences


1. Prices listed online are valid for US market and whom pay by credit card only. There will be extra charges for shipping & handling. Price various from country to country.
2. We may add extra charges for paper order and net30 terms due to extra labor cost.
3. The prices listed are subject to change without notice.