Browse Categories

Four Nozzles Spin-Spray Coater (300-3000 rpm, 12" Wafer) w/ Optional Spraying Heads - VTC-300SS-4

Please email for lead time
Transported by LTL Freight (Truck)

Product Options

Heat Lamp for Substrate Heating:
VTC-300SS-4 is the Spin-Spray Coater with four nozzles for multi-layer coating process on a large substrate up to 12". Three types of spraying heads are selectable:  The nozzle driven by compressive gas,  40KHz ultrasonic spraying head, and 120KHz ultrasonic spraying head, based on customer budget and applications. 



  • Combine the benefits of both spin and spray, enabling dense and uniform liquid-phase coating onto a large substrate
  • Four spray head to make multi-layer coating as program setting through touch screen control panel. 
  • Applications include low-temperature precipitation (e.g., for RF/microwave ferrites deposition), polymer coating, powder and composite material coating, and coating on a patterned / uneven substrate
Spin Coater
  • Vacuum chuck with adjustable substrate holders for holding flat substrate up to 12" diameter or 8" square
  • One oil-less pump for the vacuum chuck is included and controlled by the spin coater
  • Spin speed: 300 - 3000 rpm adjustable
  • For safety concerns, the speed is recommended to be limited to 2000 rpm for wafers larger than 8"
Spray Nozzles
  • Three types of the spray nozzle are selectable based on your budget
    • Four Compressive gas-driven spray heads  (Pic. 1) ( included as standard )
    • Four 40KHz ultrasonic spray nozzle with ultrasonic generator(Pic. 2)  ( optional)
    • Four120KHz ultrasonic spray nozzle with ultrasonic generator(Pic. 3)  ( optional)
    • Please click the picture below to see the details specification.
      Pic. 1   Pic. 2       Pic. 3
  • Note: Higher frequency will result in a smaller atomizing and thinner coating, but higher cost

Peristaltic Pumps

  • Fours peristaltic pumps are included for delivering four types of the solution as programma.
  • Flow rate:  0.05 - 380 ml/min programmable.
  • The four types of solution can be injected during spinning one by one with setting flow rate and duration time
  • The solenoid valves are connected to each pump to allow only one solution injection to avoid cross-contamination.
Heating Cover (optional)
  • The heatable top cover is available upon request at extra cost
  • Heating element:  Ring type of halogen lamp
  • The precision digital controller is  included with +/- 1ºC accuracy
  • Max. working temperature:  100ºC
Control Panel
  • The touch screen control panel can set programma for
    • Spin speed: 100 - 3000 rpm (not programmable)
    • Injection of solution sequence from  1 to 4  pump
    • Time of injection for each pump
    • Number of cycles
Utility Requirement
  • Power: 208 - 240 VAC, 50/60 Hz, 3000 W in total
Net Weight
  • 160 lbs
Shipping Weight & Dimensions
  • #1: 423 lbs, 48x40x42"
    #2: 155 lbs, 48x40x35"

  • CE Certified
  • NRTL certification is NOT available temporary.
  • One year limited with lifetime support
  • Rusting and damage due to improper storage condition or maintenance are not covered by warranty
Operation Manual & Video
Application Notes

  • It is the user’s responsibility to understand the risks associated with the process and use proper protectionThe process must be confined in a fume hood (Pic. 1) with proper exhaust handling capability. 
  • The film coating quality depends on the solution viscosity, substrate spin speed, substrate heating, and ultrasonic spray parameters, etc. The user is advised to experiment with the processing parameters for best results
  • Do not overflush the water bowl/base with any kind of liquid. Excess liquid will leak into the motor shaft and cause damage. Please use fabric cloth to wipe out the liquid residues in the bow/base. For more details about the cleaning procedures, please review the cleaning instruction for the spin coaters
  • In order to achieve optimal coating quality, please consider cleaning the substrate with a plasma cleaner (Click the pictures 2 & 3  below for more details) prior to coating. It will significantly reduce the surface tension on the substrates
       Pic. 1         Pic. 2    Pic. 3
Reference Articles

Related Products

Shopping Cart
Your cart is empty.
Please clear the browsing history before ordering the product. Otherwise, availability and price are not guaranteed.
Mailing Lists
MTI sponsorships:
MTI Sponsors Thermoelectrics Workshop

MTI-UCSD Battery Fabrication Lab

MTI-VISTEC Cylindrical Cell  Pilot Line

MTI Sponsors the Postdoctoral Awards

Upcoming Shows:

TMS 2022 Feb 27 - March 3 Anaheim CA Booth 509

Recent Attended Shows:
AABC USA 2021 December 7 - 9 San Diego CA Booth 429

IMAT Virtual Edition October 26 - 28

TMS 2020 Feb 23 - 27 San Diego CA Booth 700

AABC Europe Jan 12 - 16 Wiesbaden Germany

Click here to see our past conferences


1. Prices listed online are valid for the US market and who pay by credit card only. There will be extra charges for shipping & handling. Price various from country to country.
2. We may add extra charges for paper order and net30 terms due to extra labor costs.
3. The prices listed are subject to change without notice.