Browse Categories
Search

1/8" ( I.D. ) Dry Pellet Pressing Die - EQ-Die-03D


In stock
Item Number: DIE03D

Quantity Discounts

QuantityAmount
2 to 5USD$281.20
6 to 9USD$266.40
10 or moreUSD$251.60
EQ-Die-03D is a Complete pressing die with 1/8" I.D. is ready for you to make 3 mm diameter sample pellet. The pressing die is made by high-stretched and highly polished carbon steel to achieve high hardness to meet the essential requirements of making ceramic or metal samples.

SPECIFICATIONS:
Pressing die installation schematic

  • To avoid the risk of accidents and damage to the Pressing Die, please read these instructions carefully before installation and before using it for the first time.
    1. Must Read the manual especially the die installation schematic before the operation.
    2. The operator must wear protective goggles.
    3. Must have Hydraulic Pellet Press equipped with the Protection Cover   
Dimension
  1. Pressing Pole
  2. Pushing Rod
  3. Steel Sleeve
  4. Supporting Plage
  5. Withdraw Ring
                
 
     1                           2                             3                         4                            5
Material Made by High-stretched Carbon Steel 
Hardness HRC 60-62
Roughness Average (Ra) 0.08 μm
Max Load 0.72 metric Ton (at room temperature)
1000 MPa
Weight 1.1 Lbs


Whole set  pressing die includes
  • One 1/8"  I.D. core die 
  • One steel sleeve for the core-die protection
  • Two pushing rods highly polished and perfectly fitted into the die.
  • Two steel support plates
  • One pressing pole for releasing sample from die only
  • One steel cylinder for pushing out the sample

Cautions

  • WARNING:
    • DO NOT press flammable, corrosive, or explosive materials
    • The operator must wear a protection goggle.
  • Attention:
    • Use ethanol to clean the pressing die before and after use every time
    • Use anti-rust oil after the operation and store it in a dry place to avoid rusting.
    • NO pressing powder with particle size LESS THAN 30 micron should be used. Small particles may slip into the gap between the pushing rod and steel sleeve and cause damages to the sleeve during the compression.
    • Ball mill or ground the powder to the size of 32~75 microns powder before pressing.
    • .
  • Suggestions:
  • Please use a professional laboratory hydraulic press to ensure the evenness of the pressing interface 
  • For pressing sticky metal powders, such as Al, Mg, Zn, please use dry or alcohol-based lubricants to reduce friction during the compression. 

Instruction Video

    
            
Application Note You may consider using EQ-BNMR for easy mold release. Please click the picture below to order.


Steps to make sample pellet
  • Mixing and grinding chemical powder by agate mortar or Ball Mill
  • Calcine mixed the powder in a high temp furnace under suitable temperature
  • Crushing and Grinding calcined powder again by mortar or ball mill
  • Put calcined powder into the die
  • Pressing sample by a pressing machine under suitable pressure
  • Take out pellet sample from die
  • Sintering the pellet under suitable temperature in Oven
  • Then, a new material sample is formed!
Warranty
  • Pressing Dies are consumable products and are not covered by MTI's warranty.

Related Products


Pressing Die  1/8" - 3" 
Laboratory Mill & Mixer
Powder grinding & Mixing
Gravity Convection Ovens, Max. 300C
Drying Ovens

Calcining & Sintering

Hydraulic Press

CIP - Cold Isostatic Press
Shopping Cart
Your cart is empty.
Please clear the browsing history before ordering the product. Otherwise, availability and price are not guaranteed.
Mailing Lists
MTI sponsorships:
MTI Sponsors Thermoelectrics Workshop

MTI-UCSD Battery Fabrication Lab

MTI-VISTEC Cylindrical Cell  Pilot Line

MTI Sponsors the Postdoctoral Awards

Announcement:
MTI KJ Group Files Lawsuit Against Shangdong Gelon LIB Group for Copyright Infringement of MTI products and Manufacture & sale of counterfeit goods 

MTI and Celgard have successfully reached a settlement under court for the litigation on patent and trademark


Upcoming Shows:


Recent Attended Shows:
IMAT Virtual Edition October 26 - 28

TMS 2020 Feb 23 - 27 San Diego CA Booth 700


AABC Europe Jan 12 - 16 Wiesbaden Germany


Click here to see our past conferences

 

Notices
1. Prices listed online are valid for the US market and who pay by credit card only. There will be extra charges for shipping & handling. Price various from country to country.
2. We may add extra charges for paper order and net30 terms due to extra labor costs.
3. The prices listed are subject to change without notice.